** WHILE SUPPLIES LAST **
Damplifier and Damplifier Pro B-Stock - CLD Sound Deadener & Vibration Damper:
*Made In The USA*
The 40 Pounder contains 40+lbs of miscellaneous-sized pieces of Damplifier/Damplifier Pro. The estimated volume in this package is 60-90 sq ft. These packs may have factory defects such as uneven edges, wrinkles, and/or thickness variances of +/- 25%. B-Stock is made of the same material as Damplifier/Damplifier Pro.
Foil - Annealed black foil with ghosted logo
Damplifier and Damplifier Pro uses an ultra-thick 6.5 mil foil. Thicker foil means better sound deadening, vibration control, heat dissipation and easier installation with less risk of tearing.
Butyl Rubber Adhesive - High Quality American Made
High temperature butyl adhesive with increased elastomeric properties. Less fillers and more rubber means better vibration damping and noise reduction. 450 degree F thermal rating, Damplifier Pro will not melt, out gas, or fall off.
The quality of the the butyl rubber and thickness of the foil create the overall effectiveness of any C.L.D.
**Product sold as-is, no refunds or exchanges**
**Use caution when handling, the edges are very sharp**
Noise Reduction Uses...
Whether you are looking to quiet down your street rod, or make your daily driver silent like a luxury car. Damplifier Pro reduces structure borne noise that is the result of harmonics resonating from the vehicles sheet metal. Damplifier Pro stops this noise like your hand does when holding a wind chime or bell.
Damplifier Pro is a constraint layer damper that converts vibration energy into low level heat. This conversion of energy makes it 300% more efficient than tar boards and asphalt mats while weighing half as much.
Aftermarket, sound systems lose a lot of musical energy in vibrating and flexing metal panels. Not only are these vibrations loud, they also limit the potential of your stereo.
Damplifier Pro will help improve your audio system in several ways:
1. Reducing panel distortion and strengthen the area around the speakers.
2. Increasing the volume of your music by keeping the acoustical energy in the car.
3. Reducing unwanted ambient noise like road noise, engine noise & exhaust.
To help block higher frequencies of road, engine and exhaust noise, use Luxury Liner Pro on top of Damplifier Pro.
1. Ultra-thick foil layer acts as a radiant barrier, reflecting heat away.
2. Foil dissipates heat by increasing the surface area.
3. High quality made in the USA butyl rubber reduces heat transfer.
The next level of thermal insulation is to install Heatwave Pro or Luxury Liner Pro on top of Damplifier Pro.
What is the difference between Damplifier Pro and Damplifier?
Damplifier Pro is 2mm thick and Damplifier is 1mm thick.
The foil is the same at 6.5 mils. The difference is in the thickness of butyl adhesive.
What makes Second Skin Damplifier different from asphalt roofing products?
Unlike roofing products, Damplifier and Damplifier Pro use 100% butyl rubber. This is safe for use inside vehicles, virtually odorless and designed by automotive engineers. Damplifier Pro cannot be rolled because of the thickness of the foil. Thicker foil means better vibration control.
Why is Damplifier Pro not on rolls?
Products that come on rolls are roof tapes/tars relabeled as sound deadener. Quality sound insulation is manufactured in sheets, no exceptions.
How much CLD deadener do I need to use?
Covering the vehicle's interior sheet metal with 25% coverage, will reduce some harmonic distortion. In many cases 50% to 60% is necessary for effective results. With extreme bass and large engines, users may need to cover up to 100% for maximum benefits.. This depends on the intensity of the audio system, volume of road noise, engine noise or exhaust drone.
Applying a MLV noise barrier like Luxury Liner Pro on top of Damplifier pro will more than triple the results.
Why not use tar boards or asphalt?
Traditional noise mats are mostly inefficient mass loaders; heavy tar boards that work by adding weight to the cars metal. This method is over 70 years old, and is very inefficient.
Damplifier Pro Specification:
- 6.5 mil annealed foil - black with ghosted logo
- 2 mm thick (80 mils) +/- 25%
- .6 lbs. per square foot +/- 25%
- Sheet size (vary)
- Thermal range -75°F(-60°C) To 450°F(232°C)
- meets ROHS compliance standards which is an EU standard restricting the use of 10 hazardous substances.
ASTM E-756 Testing Results
Click Link Below For Data