Site Information

 Loading... Please wait...
  • Compare
  • Gift Certificates
  • My Account
  • All prices are in USD

Audio Door Kit Premium (4 Doors) - Bulk Pack, Speaker Tweaker Set of 4, 4 Sheets LLP, 1CSA, 1WHR

Shipping:
Calculated at checkout
Quantity:

Product Description

Second Skin's Premium Audio Door Kit (4 Doors) is the perfect small project for a big return for vehicles with 3/8" clearance in the doors and a little bigger then the average door! With enough product to completely insulate 4 large vehicle doors from road noise, heat, and internal interference/squeaks and rattles, if you're looking for something you can simply add to your cart and get going this is the item for you. This audio door kit upgrades the Over Kill Pro Closed Cell Foam layer of the regular Audio Door Kit with the much denser and more sound dampening material of Luxury Liner Pro Mass Loaded Vinyl/Closed Cell Foam infused into one layer. 

Premium Audio 4 Door Kit Contains: 

1 - 36.5 sqft Damplifier Pro Bulk Pack - 22 Sheets at 12" x 20" 

4 - 9 sqft Luxury Liner Pro at 24" x 54" and 3/8" Thick MLV/CCF Each Sheet (36 sqft Total)

1 - Speaker Tweaker Kit (Set of Four)

1 - Can of High Heat Spray Adhesive 

1 - Wooden Hand Roller

Enough Product For 4 Vehicle Doors

 Instructions:

First, install the damplifier pro on the interior side of the outer door skin (the metal skin you see from the outside of the car).

After that's done, install the Luxury Liner Pro on top of the Damplifier Pro. To use Second Skin's high temp adhesive, simply apply a layer to both the product you're going to install AND the surface you wish to apply it to (be sure both surfaces are clean and free of solvent residue). Allow about 60-90 seconds for the adhesive to tack up, press the two surfaces together. hold firmly for another 30-60 seconds.

The last thing to do is use Super Glue/Double Sided Tape on the Speaker Tweaker Pads. Install the pads directly behind your door speakers for the best results. Speaker Pads may be cut in half and installed on both sides of the support bar.

Damplifier Pro:

Whether you are looking to quiet down your street rod, or make your daily driver comfortable as a luxury car, Damplifier Pro is the strongest, most resilient vibration damper on the market.

The first acoustical problem in any sound deadening project is structure borne noise This is the harmonics and resonance that is emitted from the cars sheet metal panels, similar to a wind chime. Unlike wind chimes however, our cars are not tuned to any specific musical frequency, so what we end up hearing is the road noise, engine rumble and exhaust drone.

Stopping the vibrations on your cars metal panels is much like stopping a noisy wind chime with your hand. Once the vibrations stop, the  structure borne noise stops.

Traditional noise mats are mostly inefficient mass loaders; heavy & foul smelling tar boards that work by adding weight to the cars metal to quiet it down. This technology is over 50 years old, and for some reasons, is still being promoted by many of our competitors.

Damplifier Pro is not a mass loader or a heavy tar board. 
It is a constraint layer viscoelastic damper that converts the vibrational energy in to low level heat. This conversion of energy makes it 300% more efficient than traditional mass loading tar boards and asphalt mats while weighing half as much!

Simply cut, peel and stick Damplifier Pro to the interior sheet metal of your car to block out unwanted structure borne noise!

Luxury Liner Pro:

Applying a layer of Luxury Liner Pro inside the doors on top of your Damplifier or Spectrum vibration dampers is the easiest way to improve the acoustics from your door speakers.

First, Luxury Liner Pro will reduce the airborne sound waves that are able to penetrate the vibration damper. This reduction in unwanted noise will equate to in increase in the desired noise which is your music.

Luxury Liner Pro will also reduce the intensity of distortion causing reflections inside your vehicle. The less noise that is bouncing around the car walls, the louder and clearer your audio system will sound.

Speaker Tweaker Pads:

These dynamic pads are the easiest way to clean up the mid range and mid bass from your door speakers or kick pods.

Simply adhere one Speaker Tweaker pad 2-8 inches behind your door speakers, with the ridges facing the speakers, to absorb and redirect the rear wave away from the back of the speaker. Redirecting the rear wave will help reduce distortion and will improve the mid register of your music.

 

**Alway use caution when handling Damplifier products, the foil edges are very sharp**

Noise Reduction Uses...

Damplifier Pro:

Whether you are looking to quiet down your street rod, or make your daily driver comfortable as a luxury car, Damplifier Pro is the strongest, most resilient vibration damper on the market.

The first acoustical problem in any sound deadening project is structure borne noise This is the harmonics and resonance that is emitted from the cars sheet metal panels, similar to a wind chime. Unlike wind chimes however, our cars are not tuned to any specific musical frequency, so what we end up hearing is the road noise, engine rumble and exhaust drone.

Stopping the vibrations on your cars metal panels is much like stopping a noisy wind chime with your hand. Once the vibrations stop, the  structure borne noise stops.

Traditional noise mats are mostly inefficient mass loaders; heavy & foul smelling tar boards that work by adding weight to the cars metal to quiet it down. This technology is over 50 years old, and for some reasons, is still being promoted by many of our competitors.

Damplifier Pro is not a mass loader or a heavy tar board. 
It is a constraint layer viscoelastic damper that converts the vibrational energy in to low level heat. This conversion of energy makes it 300% more efficient than traditional mass loading tar boards and asphalt mats while weighing half as much!

Simply cut, peel and stick Damplifier Pro to the interior sheet metal of your car to block out unwanted structure borne noise!

Luxury Liner Pro:

Applying a layer of Luxury Liner Pro inside the doors on top of your Damplifier or Spectrum vibration dampers is the easiest way to improve the acoustics from your door speakers.

First, Luxury Liner Pro will reduce the airborne sound waves that are able to penetrate the vibration damper. This reduction in unwanted noise will equate to in increase in the desired noise which is your music.

Luxury Liner Pro will also reduce the intensity of distortion causing reflections inside your vehicle. The less noise that is bouncing around the car walls, the louder and clearer your audio system will sound.

Speaker Tweaker Pads:

These dynamic pads are the easiest way to clean up the mid range and mid bass from your door speakers or kick pods.

Simply adhere one Speaker Tweaker pad 2-8 inches behind your door speakers, with the ridges facing the speakers, to absorb and redirect the rear wave away from the back of the speaker. Redirecting the rear wave will help reduce distortion and will improve the mid register of your music.

Mobile Audio

Damplifier Pro:

Whether you are looking to quiet down your street rod, or make your daily driver comfortable as a luxury car, Damplifier Pro is the strongest, most resilient vibration damper on the market.

The first acoustical problem in any sound deadening project is structure borne noise This is the harmonics and resonance that is emitted from the cars sheet metal panels, similar to a wind chime. Unlike wind chimes however, our cars are not tuned to any specific musical frequency, so what we end up hearing is the road noise, engine rumble and exhaust drone.

Stopping the vibrations on your cars metal panels is much like stopping a noisy wind chime with your hand. Once the vibrations stop, the  structure borne noise stops.

Traditional noise mats are mostly inefficient mass loaders; heavy & foul smelling tar boards that work by adding weight to the cars metal to quiet it down. This technology is over 50 years old, and for some reasons, is still being promoted by many of our competitors.

Damplifier Pro is not a mass loader or a heavy tar board. 
It is a constraint layer viscoelastic damper that converts the vibrational energy in to low level heat. This conversion of energy makes it 300% more efficient than traditional mass loading tar boards and asphalt mats while weighing half as much!

Simply cut, peel and stick Damplifier Pro to the interior sheet metal of your car to block out unwanted structure borne noise!

Luxury Liner Pro:

Applying a layer of Luxury Liner Pro inside the doors on top of your Damplifier or Spectrum vibration dampers is the easiest way to improve the acoustics from your door speakers.

First, Luxury Liner Pro will reduce the airborne sound waves that are able to penetrate the vibration damper. This reduction in unwanted noise will equate to in increase in the desired noise which is your music.

Luxury Liner Pro will also reduce the intensity of distortion causing reflections inside your vehicle. The less noise that is bouncing around the car walls, the louder and clearer your audio system will sound.

Speaker Tweaker Pads:

These dynamic pads are the easiest way to clean up the mid range and mid bass from your door speakers or kick pods.

Simply adhere one Speaker Tweaker pad 3-8 inches behind your door speakers, with the ridges facing the speakers, to absorb and redirect the rear wave away from the back of the speaker. Redirecting the rear wave will help reduce distortion and will improve the mid register of your music.

Thermal Insulation

 Damplifier Pro is not only our best sound deadening mat, but it also is one mean thermal insulator. The ultra thick foil on Damplifier Pro offers three thermal insulation benefits.

First, the foil acts as a radiant barrier, reflecting heat back towards the source. When used on the firewall, this reduces the amount of heat from making it in to the cabin of the car. Less heat means cooler temperatures. Pretty simple.

Second, the foil heat shield on Damplifier Pro dissipates heat by increasing the surface area, allowing for thermal dissipation and reduction.

Third, the butyl layer slows down any remaining heat on its way in to the cabin of the car. The longer it takes the heat to get to you, the more comfortable you are.

Damplifier Pro is a thermal insulator much like a coffee thermos. If you put hot liquid in the thermos, it stays hot for longer. If you put ice water inside, the ice takes longer to melt. 

The Luxury Liner Pro can greatly increase the thermal insulation by adding thousands of little packets which slow the transfer of heat. These are the "cells" refereed to in the term "closed celled foam"

FAQ

What is the difference between Damplifier Pro and Damplifier automotive vibration damping mats??
Damplifier and Damplifier Pro are the same basic automotive CLD sound deadener mats in terms of product quality, but Damplifier Pro has a total thickness that is twice as thick as our regular automotive vibration mat Damplifier.
The foil on both of our automotive sound deadeners is the same; both 6.5 mils thick. The only difference between the two products is the total thickness of the adhesive. 

What makes Second Skin Damplifier different from asphalt roofing products or sound deadeners that come one rolls?
At Second Skin, we only sell sound deadening products that are specifically designed for automobiles. Unlike roofing products, our CLD vibration damping mats Damplifier and Damplifier Pro use 100% butyl binders with no cheap asphalt filler.  Our CLD sound deadening dampers are non toxic, odorless and designed by automotive industry experts.
The foil on our CLD sound deadener Damplifier Pro is 3 times thicker than that of most roofing products and will not melt, or fail.

Why does Damplifier Pro not come on a roll like less expensive Sound deadening mats do?
Here is an industry secret. Products that come on rolls are roof tapes relabeled as CLD sound deadener mats. There is not a sound deadening manufacturer in the industry that puts CLD constraint layer dampers on a roll. Real sound deadening vibration damper mats will always come in sheets. If it is on a roll, it is not designed as a sound deadener. It came from a roofing manufacturer and was not designed to dampen vibrations in a car. There is no exception to this rule. Companies that sell roofing tape to customers as sound deadening mats, are doing a great disservice to the automotive sound deadening industry, and are ripping off customers for their hard earned money.

How much CLD sound deadening do I need to use in my car to properly sound deaden the vibrations?
When it comes to automotive sound deadening and vibration damping. more is always better, to a point. Covering the flat panels of your cars interior sheet metal panels with as little as 25 percent will reduce harmonic distortion, however in many cases, as much as 50 or 100 percent  CLD sound deadening coverage might be needed, depending on the intensity of the audio system or how loud the road noise, engine noise and exhaust drone is. Applying a MLV noise barrier like our Luxury Liner Pro on top of your CLD sound deadener will more that triple the sound deadening results from your Damplifier application.

 

Specification

Damplifier Pro:

  • 6.5 mil  foil -BLACK
  • 2 mm total thickness (80 mils) +/- 5%
  • Adhesive = Viscoelastic butyl rubber - 99.94% solids content
  • .6 lbs per square foot +/- 5% 
  • 12" x 20" (1.67 sq ft.)
  • High temperature butyl adhesive with increased elastomeric properties
  • Higher rubber content - Less filler content = better performance

 Luxury Liner Pro:

  • Sheet size =  24" x 54" (9 sq. feet)
  • Thickness = 3/8"  
  • Mass/Area = 1.0 lbs. per sq foot
  • Total weight per sheet = 9.0 lbs. per sheet 

* Requires contact spray adhesive (1 can per 4 sheets)

Speaker Tweaker Kit:

  • (2) 7" diameter Second Skin back wave canceling discs

 

Technical Data

Damplifier Pro

Product Videos

How To Sound Deaden Doors 06:56

Learn how to apply Sound Deadener such as Second Skin Damplifier Pro to vehicle doors. Please subscribe for more and like us at https://www.facebook.com/ShowTimeCarAudio.net Visit my webstore at http://showtimecaraudio.net/

  • How To Sound D...
    Learn how to apply Sound Deadener such as Second Skin Damplifi...
  • Second Skin - ...
    Buzz Thompson from www.floridaspl.com Installing Second Skin D...
  • SecondSkin Ane...
    Anechoic means to be without echo. SecondSkin Audio offers Spe...
  • Sound Deaden t...
    Check out the sound system install here: http://www.stevemeade...

Find Similar Products by Tag

Product Reviews

Write Review

This product hasn't received any reviews yet. Be the first to review this product!

Find Similar Products by Category